Just How to Remove as Well as Replace a Bath Tub
Just How to Remove as Well as Replace a Bath Tub
Blog Article
On this page in the next paragraph you will find additional sensible details on the subject of Tools You Need to Install a New Bathtub .
Setting up a tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably challenging project. If the old bathtub is conveniently easily accessible, the project can move easily; if you need to open a wall to get rid of the old tub and place the brand-new bathtub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly need an assistant to leave the old tub and also embeded in the new one. See to it you have actually qualified on your own for the task and fit attempting it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to consider using one before you begin. Chances are you might require a specialist plumber to make tube connections.
This article will certainly help you mount a new bath tub in your restroom if you have actually already acquired a new bathtub and also don't require to transform the plan of your previous water pipes.
Your tools and also material checklist must consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome because of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
Prior to going on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet as well as the sink. Protect the faucet in place with the producer offered backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former type should be attached to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Making use of the two wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 small points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the bathtub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water system and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as likewise check the overflow electrical outlet and the regular electrical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been utilized at least when as this will resolve it right into its final placement.
Getting ready for the Installation
First of all, the sustaining framework provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to penetrate the wall between the bath and the tiling, resulting in issues with moisture as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and cartridges, and are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can break fairly very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about Tools You Need to Install a New Bathtub , I figured sharing that excerpt was a good idea. Do you know somebody else who is occupied with Tools You Need to Install a New Bathtub ? Feel free to share it. We thank you for reading our article about Installing A Bathtub.
Apply Now
Report this page